66V 150A 22S 22x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 66V 150A 22S 22x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 66V 150A 22S 22x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 66V 150A 22S 22x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System

66V 150A 22S 22x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System

  • Model: 66V 22S 150A LiFePO4 LFP BMS
  • Shipping Weight: 1.8kg
  • Units in Stock: 9999

$96.00

Add to Cart:



  • Products description
  • Reviews
  • Reviews write
  • Shipping
  • Privacy Policy
  • Contact us
 
66V   70.4V   80V   150A   22S  LiFePo4 Battery Pack BMS for E-bike
22S  150A  lithium LiFePO4 Battery protection board
 
 photo P1150001ss.jpg
 
Technical Parameters:
Balanced current: 60mA (VCELL = 3.90V when)
Balanced for: 3.50 ± 0.05 V
Over-charged Protection: 3.85 ± 0.05 V
Over-discharged Protection: 2.1 ± 0.05 V
Over-charged delay: 1 ± 0.5S
Over-charged release: 3.80 ± 0.05 V
Over-discharged threshold: 2.10 ± 0.05 S
Over-discharged delay: 100 ± 50mS
Over-current Protecton: 150 A
Supports Max. Continuing Discharge Current: 150A
Static power consumption: less than 200uA
Short-circuit protection function: disconnect the load from the recovery.
 
Dimension: 182mm * 85mm *40mm
 
Feature: With Aluminum Protected Outer Shell and built-in Radiating board
 
The main functions: Over-charged, Over-discharged protection, short circuit protection, over-current protection, with Balancing function.
 
Interface Definition: The board have balancing function. So you may see a balance connector with 22 wires, when you do the connection for the 22S batteries, start from the first Red wire, then connect other Grey wires one by one, dont make wrong orderly as this will get the BMS burnt, check battery voltage step by step, it start from 3.2V and increases with (3.2V~3.6V) one by one to make 66V (80V) finally. Check every voltage increase with below parameter:
 
3V-6V-9V-12V-15V-18V-21V-24V-27V-30V-33V-36V-39V-42V-45V-48V-51V-54V-57V-60V-63V-66V

 photo LiFePO4 24S 150A LOGO.jpg

The 3 thick Black wires connect to battery pack Negative, and 3 thick Yellow wires for Motor / Controller ( Discharge) Negative, and 1 thin Black wire for charger Negative.

Charge & Discharge Positive could be the same output.

The BMS only works for Brand new good quality battery with perfect performance, it cant work for fake capacity and used batteries. 

 
Check every voltage on the wire step by step before plug in the connector.  Check every wire and see if the orderly are correct. Because if any of the wire get a wrong order, it will get burnt. Smoke shows board already get burnt for protecting the battery being damaged by wrong connection,  For DIY assembling. Please make sure you are capable to do the assembling before ordering! If you dont know how to do the connection, DONT ORDER IT!
 
 
IMPORTANT!!!
  • The BMS only use for new and consistent high drain batteries. 
  • Do not use for battery packs that mix with new & half-used, or mix with different brand battery cells.
  • Do not use for used and imbalance battery cells.
  • Do not use for batteries with fake capacity.
  • Do not touch the board by hand while it is charging / discharging.
  • If you charge the battery by LiFePO4 Balance Charger, then there's no need to use BMS.
 
Battery not including, the auction is for BMS only.
Balance Connector will send together with the BMS.
 
 
You may also check with charger info. from our online Categories:
Categories - Battery Chargers - LiFePO4 eBike Charger - 80.3V 3A LiFePO4 Charger
 
 
Wholesale Welcome!


digital ballast
 
 
We are having Spring
Festival from
Jan. 30 ~ Feb. 30,  
business will resume
on March.
 
All you message will
be checked and replied
during the holiday, but
may have some delay
reply. Orders will be
processed after the
holiday.
 
Urgent issue contact:
supowerbattery@gmail.com