60V 80A 20S 20x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 60V 80A 20S 20x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 60V 80A 20S 20x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System
  • 60V 80A 20S 20x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System

60V 80A 20S 20x 3.2V LiFePo4 Battery BMS LFP PCB PCM SMT System

  • Model: 60V 20S 80A LiFePO4 LFP BMS
  • Shipping Weight: 1.8kg
  • Units in Stock: 9998

$73.00

Add to Cart:



  • Products description
  • Reviews
  • Reviews write
  • Shipping
  • Privacy Policy
  • Contact us
 
60V  64V   80A   20S  LiFePo4 Battery Pack BMS for E-bike
20S  80A  lithium LiFePO4 Battery protection board.
 
 photo P1150001ss.jpg
 
Technical Parameters:
Balanced current: 60mA (VCELL = 3.90V when)
Balanced for: 3.50 ± 0.05 V
Over-charged Protection: 3.85 ± 0.05 V
Over-discharged Protection: 2.1 ± 0.05 V
Over-charged delay: 1 ± 0.5S
Over-charged release: 3.80 ± 0.05 V
Over-discharged threshold: 2.10 ± 0.05 S
Over-discharged delay: 100 ± 50mS
Over-current Protecton: 80 A
Supports Max. Continuing Discharge Current: 80A
Static power consumption: less than 200uA
Short-circuit protection function: disconnect the load from the recovery.
 
Dimension: 182mm * 85mm *40mm
 
Feature: With Aluminum Protected Outer Shell and built-in Radiating board
 
The main functions: Over-charged, Over-discharged protection, short circuit protection, over-current protection, with Balancing function.
 
Interface Definition: The board have balancing function. So you may see a balance connector with 20 wires, when you do the connection for the 20S batteries, start from the first Red wire, then connect other Grey wires one by one, dont make wrong orderly as this will get the BMS burnt, check battery voltage step by step, it start from 3.2V and increases with (3.2V~3.6V) one by one to make 60V (64V) finally. Check every voltage increase with below parameter:

3V - 6V - 9V - 12V - 15V - 18V - 21V - 24V - 27V - 30V - 33V - 36V - 39V - 42V - 45V - 48V - 51V - 54V - 57V - 60V

 photo LiFePO420Slogo.jpg

The 2 thick Black wires connect to battery pack Negative, and 2 thick Yellow wires for Motor / Controller ( Discharge) Negative, and 1 thin Yellow wire for charger Negative.

Charge & Discharge Positive could be the same output.

The BMS only works for Brand new good quality battery with perfect performance, it cant work for fake capacity and used batteries. 

 
Check every voltage on the wire step by step before plug in the connector.  Check every wire and see if the orderly are correct. Because if any of the wire get a wrong order, it will get burnt. Smoke shows board already get burnt for protecting the battery being damaged by wrong connection,  For DIY assembling. Please make sure you are capable to do the assembling before ordering! If you dont know how to do the connection, DONT ORDER IT!
 
 
IMPORTANT!!!
  • The BMS only use for new and consistent high drain batteries. 
  • Do not use for battery packs that mix with new & half-used, or mix with different brand battery cells.
  • Do not use for used and imbalance battery cells.
  • Do not use for batteries with fake capacity.
  • Do not touch the board by hand while it is charging / discharging.
  • If you charge the battery by LiFePO4 Balance Charger, then there's no need to use BMS.
 
Battery not including, the auction is for BMS only.
Balance Connector will send together with the BMS.
 
 
You may also check with charger info. from our online Categories:
Categories - Battery Chargers - LiFePO4 eBike Charger -  73V  5A LiFePO4 Charger
 
 
Wholesale Welcome!
 


digital ballast
 
 
Please choose 
"Zone Rate" shipment
for economic shipping.
 
Shipment for Lithium
battery is slow, we 
could only send
battery produtcs to
U.S., AU and some
European countries.
 
Inquiries please send to:
supowerbattery@gmail.com