22V 24V 6S 30A 6x 3.6V Lithium ion LiPo Battery BMS PCM PCB [22V 6S 30A Lion LiPO BMS] - $29.00 : Lithium Rechargeable Batteries, Battery BMS, Pack Assembling

Categories

Products description
Reviews
Reviews write
Shipping
Privacy Policy
Contact us

22V 24V 25.2V 30A 6S Lithium ion / LiPolymer Battery Pack BMS for E-bike

6S 30A Li-ion / LiPO Battery protection board.

Applicable for

21.6V (3.6V * 6S) lithium battery & packs

22.2V (3.7V * 6S) lithium battery & packs

25.2V (4.2V * 6S) lithium battery & packs

Lithium battery (Li-ion)

Prismatic Lithium Polymer battery (Li-Po)

Technical Parameters:

Balanced current: 60mA (VCELL = 3.90V when)

Balanced for: 4.20 ± 0.05 V

Over-charged Protection: 4.2 ± 0.05 V

Over-charged Release: 4.05 ± 0.05 V

Over-discharged Protection: 2.9 ± 0.05 V

Over-charged delay: 5mS

Over-current Protecton: 30 A

Supports Max. Continuing Discharge Current: 30A

Static power consumption: less than 200uA

Short-circuit protection function: disconnect the load from the recovery.

Dimension: 102mm * 53mm

The main functions: Over-charged, Over-discharged protection, short circuit protection, over-current protection, with Balancing function.

Interface Definition:

The board have balancing function. So you may see a balance connector with 6 wires, below chart shows how to connect the wires onto 6 batteries to realize balancing and protection.

The Positive output on Battery Pack (22V + ) could connecting to charger positive pole (charger +)
Battery Pack (22V -) connecting with B- on board
Chip board P- connecting to Charger Negative Pole (charger -)
Chip board P- could be Negative output for charger, motor, controller
Battery B+ could be Positive output for charger, motor, controller

1, The charging port and the discharge port of the board are the same Positive port. “B-“ for negative Pole of the battery pack, “P-“ is negative pole for both discharging and charging.

2, “B-“, “N-“ , “P-“ welding pad are through-hole port, hole diameter of 3.5 mm; You could use solder iron to weld the wires through the hole port, Every charging port for battery are the DC needle seat forms output. “N-“ with no wiring when charging and discharging are in the same port;

3, First connect the “P-“ , “B-“ to the battery pack, then re-check with the battery voltages, then connect the 6 wires onto the batteries, Do not connect in wrong ordering, or it will burn out the board.

If you made wrong connection and reverse the board that will cause smoke, please check with every wire to be sure you are doing correct connection.

check all the wires voltage with orderly, start from B- , and see if it increasing from 3.6V, like:

( wires / voltage )

1 - 2 - 3 - 4 - 5 - 6

3.7V - 7.4V - 11.1V - 14.8V - 18V - 22V

Check every voltage on the wire step by step before plug in the connector. Check every wire and see if the orderly are correct. Because if any of the wire get a wrong order, it will get burnt. Smoke shows board already get burnt for protecting the battery being damaged by wrong connection, For DIY assembling. Please make sure you are capable to do the assembling before ordering! If you dont know how to do the connection, DONT ORDER IT!

IMPORTANT!!!

The BMS only use for new and consistent high drain batteries.
Do not use for battery packs that mix with new & half-used, or mix with different brand battery cells.
Do not use for used and imbalance battery cells.
Do not use for batteries with fake capacity.
Do not touch the board by hand while it is charging / discharging.
If you charge the battery by Lithium Balance Charger, then there's no need to use BMS.

Battery not including, the auction is for BMS only.

Balance Connector will send together with the BMS.

You may also check with charger info. from our online Categories:

Categories - Battery Chargers - Lion LiPO eBike Charger - 25.2V 5A Lithium Charger

Wholesale Welcome!

Shipping:

Items will be shipped out in 24-48 hours (excluding weekend or holidays).
We will ship with the delivery address according to your Paypal payment,please be sure your shipping address is correct
when you pay.
Small packages less than 2kg will ship by registered mail service, most of the areas normally take about 14-20 days to
deliver.
Some countries may take over 30 days to deliver, you may refer to " F.A.Q" page, " Shipping & Delivery" for further info.
We also offer optional UPS / TNT / Fedex Express service with higher freight cost but fast delivery.
Lithium Battery with strict restriction for air shipping. For parcel under 2KG, it could ship by HK SAL Sea Transportation (Zone Rates)
with low cost but shipment would be very slow.
If you can't wait for long delivery for battery products, there's optional Expedited Shipping (TNT / UPS / Fedex) for
selection.
All the shipments will have a tracking number to trace with.

If you do not receive the package over 50 days, please contact us, we will check with the shipping status for you.
Items will be labeled as Gift or Toy Components with under invoicing to avoid import tax. In most of the case,
package will not have any import tax and or handling charges, if any custom tariff duties, buyers will be
responsible to pay the import tax.

Customers who bought this product also purchased...

Battery Transparent Electronic Insulated adhesive tape

14AWG Flexible Silicone Wire 1m Red +1m Black Heatproof 200°C

3S 10.8V 11.1V 20A Lithium ion Battery Protection Circuit Board

Li-ion Li-Po 25.9V 29.4V 2A 7S Wall Socket Battery Charger AC DC

1m 10 W x 0.15 T Pure Nickel strip tape for A123 26650 Battery

10x JST-XH 6S Connector B6 Balance Plug 7 Pin 22AWG 21.6V 19.2V